Document Center List of Standards on Chemical Laboratories. Laboratory Equipment Including Hydrometers, Alcoholometers, Etc. Apparatus For Measurement Of Volume, Mass, Density, Viscosity, See 17.060 Spectroscopes, See 17.180.30 Temperature-Measuring Instruments, See 17.200.20 Laboratory Ware, See 71.040.20
ICS Code 71.040.10
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
- ASTM-C1222 - Standard Practice for Evaluation of Laboratories Testing Hydraulic Cement
- ASTM-C1426 - Standard Practices for Verification and Calibration of Polarimeters
- ASTM-D4178 - Standard Practice for Calibrating Moisture Analyzers
- ASTM-D5423 - Standard Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation
- ASTM-D7969 - Standard Specification for Gravity Convection and Forced Ventilation Ovens
- ASTM-E1206 - Guide for Computerization of Existing Equipment (Withdrawn 2000)
- ASTM-E133 - Standard Specification for Distillation Equipment
- ASTM-E145 - Standard Specification for Gravity-Convection and Forced-Ventilation Ovens
- ASTM-E1581 - Practice for Using Pre-Control in the Instrumental/Analytical Laboratory (Withdrawn 1998)
- ASTM-E2335 - Standard Guide for Laboratory Monitors
- ASTM-E2402 - Standard Test Method for Mass Loss, Residue, and Temperature Measurement Validation of Thermogravimetric Analyzers
- ASTM-E95 - Standard Specification for Cell-Type Oven with Controlled Rates of Ventilation
- ASTM-F2875 - Standard Guide for Laboratory Requirements Necessary to Test Commercial Cooking and Warming Appliances to ASTM Test Methods
BSI:
- BS-2586 - Specification for glass and reference electrodes for the measurement of pH
- BS-2646-1 - Autoclaves for sterilization in laboratories
- BS-2646-2 - Autoclaves for sterilization in laboratories
- BS-2646-2-TC - Tracked Changes. Autoclaves for sterilization in laboratories
- BS-2646-3 - Autoclaves for sterilization in laboratories
- BS-2646-4 - Autoclaves for sterilization in laboratories
- BS-2646-5 - Autoclaves for sterilization in laboratories
- BS-2648 - Performance requirements for electrically-heated laboratory drying ovens
- BS-3145 - Specification for laboratory pH meters
- BS-3202 - Recommendations on laboratory furniture and fittings
- BS-3202-1 - Laboratory furniture and fittings. Introduction
- BS-3202-2 - Laboratory furniture and fittings
- BS-4309 - Methods of measuring the performance of laboratory electric resistance furnaces
- BS-4314-1 - Specification for apparatus for physical methods of gas analysis. Infra-red gas analysers for industrial use
- BS-5470 - Specification for glass alcohol hydrometers not incorporating a thermometer
- BS-5726-2 - Microbiological Safety Cabinets, Recommendations for Information To Be Exchanged Betwe
- BS-5726-3 - Microbiological Safety Cabinets, Specification for Performance After Installation
- BS-5726-4 - Microbiological Safety Cabinets, Recommendations for Selection, Use & Maintenance
- BS-5865 - Specification for construction and operation of spirit burner for small-scale laboratory flame tests
- BS-7183 - Guide to design of test rooms for sensory analysis of food
- BS-7310 - Specification for ion-selective electrodes, reference electrodes, combination electrodes and ion-selective electrode meters for determination of ions in solution
- BS-767 - Specification for centrifuges of the basket and bowl type for use in industrial and commercial applications
- BS-894 - Specification for Ubbelohde apparatus for flow and drop points
- BS-EN-12469 - Biotechnology. Performance criteria for microbiological safety cabinets
- BS-EN-12547 - Centrifuges. Common safety requirements
- BS-EN-13150 - Workbenches for laboratories. Dimensions, safety requirements and test methods
- BS-EN-13150-TC - Tracked Changes. Workbenches for laboratories in educational institutions. Dimensions, safety and durability requirements and test methods
- BS-EN-13792 - Colour coding of taps and valves for use in laboratories
- BS-EN-14175-1 - Fume cupboards
- BS-EN-14175-2 - Fume cupboards
- BS-EN-14175-3 - Fume cupboards
- BS-EN-14175-4 - Fume cupboards
- BS-EN-14175-6 - Fume cupboards
- BS-EN-14175-7 - Fume cupboards
- BS-EN-14175-8 - Fume cupboards
- BS-EN-14470-1 - Fire safety storage cabinets
- BS-EN-14470-1-TC - Tracked Changes. Fire safety storage cabinets
- BS-EN-14470-2 - Fire safety storage cabinets
- BS-EN-14727 - Laboratory furniture. Storage units for laboratories. Requirements and test methods
- BS-EN-15154-1 - Emergency safety showers
- BS-EN-15154-2 - Emergency safety showers
- BS-EN-15154-3 - Emergency safety showers
- BS-EN-15154-4 - Emergency safety showers
- BS-EN-15154-5 - Emergency safety showers
- BS-EN-15154-6 - Emergency safety showers
- BS-EN-16589-1 - Laboratory local exhaust devices
- BS-EN-16589-1-TC - Tracked Changes. Laboratory local exhaust devices
- BS-EN-61010-2-020 - Safety requirements for electrical equipment for measurement, control, and laboratory use
- BS-EN-61010-2-020-TC - Tracked Changes. Safety requirements for electrical equipment for measurement, control, and laboratory use
- BS-EN-61010-2-033 - Safety requirements for electrical equipment for measurement, control, and laboratory use
- BS-EN-61010-2-040 - Safety requirements for electrical equipment for measurement, control, and laboratory use
- BS-EN-61010-2-040-TC - Tracked Changes. Safety requirements for electrical equipment for measurement, control, and laboratory use
- BS-EN-61010-2-081 - Safety requirements for electrical equipment for measurement, control and laboratory use
- BS-EN-61010-2-091 - Safety requirements for electrical equipment for measurement, control and laboratory use
- BS-EN-61010-2-101 - Safety requirements for electrical equipment for measurement, control and laboratory use
- BS-EN-61010-2-101-TC - Tracked Changes. Safety requirements for electrical equipment for measurement, control and laboratory use
- BS-EN-61207-1 - Expression of performance of gas analyzers
- BS-EN-IEC-61010-2-030 - Safety requirements for electrical equipment for measurement, control, and laboratory use
- BS-EN-IEC-61010-2-033 - Safety requirements for electrical equipment for measurement, control, and laboratory use
- BS-EN-IEC-61010-2-034 - Safety requirements for electrical equipment for measurement, control, and laboratory use
- BS-EN-IEC-61010-2-040 - Safety requirements for electrical equipment for measurement, control, and laboratory use
- BS-EN-IEC-61010-2-081 - Safety requirements for electrical equipment for measurement, control and laboratory use
- BS-EN-IEC-61010-2-101 - Safety requirements for electrical equipment for measurement, control, and laboratory use
- BS-EN-IEC-61207-2 - Expression of performance of gas analyzers
- BS-EN-ISO-10991 - Microfluidics. Vocabulary
- BS-EN-ISO-10991-TC - Tracked Changes. Microfluidics. Vocabulary
- BS-IEC-61010-3 - Safety requirements for electrical equipment for measurement, control, and laboratory use
- BS-IEC-61010-3-051 - Safety requirements for electrical equipment for measurement, control, and laboratory use
- BS-IEC-61010-3-061 - Safety requirements for electrical equipment for measurement, control, and laboratory use
- DD-61010-100 - Safety requirements for electrical equipment for measurement, control and laboratory use
- DD-80-1 - Laboratory fume cupboards
- DD-80-2 - Laboratory fume cupboardsRecommendations for information to be exchanged between purchaser, vendor and installer and recommendations for installation
- DD-80-3 - Laboratory fume cupboards
- DD-CEN-14175-5 - Fume cupboards
- PD-CEN-16589 - Laboratory installations. Capture devices with articulated extract arm
- PD-CEN-17441 - Laboratory installations. Ventilation systems in laboratories
- PD-IEC-61010-3-041 - Safety requirements for electrical equipment for measurement, control, and laboratory use
- PD-IEC-61010-3-042 - Safety requirements for electrical equipment for measurement, control, and laboratory use
IEC:
- IEC-61010-1 - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements
- IEC-61010-1-AM1 - Amendment 1 - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements
- IEC-61010-2-020 - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-020: Particular requirements for laboratory centrifuges
- IEC-61010-2-020-RL - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-020: Particular requirements for laboratory centrifuges
- IEC-61010-2-030 - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-030: Particular requirements for equipment having testing or measuring circuits
- IEC-61010-2-030 EXV - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-030: Particular requirements for equipment having testing or measuring circuits
- IEC-61010-2-030-RL - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-030: Particular requirements for equipment having testing or measuring circuits
- IEC-61010-2-033 - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-033: Particular requirements for hand-held multimeters and other meters for domestic and professional use, capable of measuring mains voltage
- IEC-61010-2-033 EXV - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-033: Particular requirements for hand-held multimeters and other meters for domestic and professional use, capable of measuring mains voltage
- IEC-61010-2-033-RL - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-033: Particular requirements for hand-held multimeters and other meters for domestic and professional use, capable of measuring mains voltage
- IEC-61010-2-034 - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-034: Particular requirements for measurement equipment for insulation resistance and test equipment for electric strength
- IEC-61010-2-034-EXV - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-034: Particular requirements for measurement equipment for insulation resistance and test equipment for electric strength
- IEC-61010-2-040 - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-040: Particular requirements for sterilizers and washer-disinfectors used to treat medical materials
- IEC-61010-2-081 - Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-081: Particular requirements for automatic and semi-automatic laboratory equipment for analysis and other purposes
- IEC-61010-2-081-RL - Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-081: Particular requirements for automatic and semi-automatic laboratory equipment for analysis and other purposes
- IEC-61010-2-091 - Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-091: Particular requirements for cabinet X-ray systems
- IEC-61010-2-091-RL - Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-091: Particular requirements for cabinet X-ray systems
- IEC-61010-3 - Part 3: Protocol for the Preparation of Conformity Verification Reports for the IEC 61010
- IEC-61010-3-031 - Part 3-031: Conformity Verification Report for IEC 61010-031: 2002 - Safety Requirements F
- IEC-61010-3-045 - Part 3-045: Conformity Verification Report for IEC 61010-2-045: 2000 - Particular Requirem
- IEC-61010-3-081 - Part 3-081: Conformity Verification Report for IEC 61010-2-081: 2001 - Particular Requirem
- IEC-61010-3-1 - Part 3-1: Conformity Verification Report for IEC 61010-1: 2001 - General Requirements, Saf
- IEC-61010-3-101 - Part 3-101: Conformity Verification Report for IEC 61010-2-101: 2002 - Particular Requirem
ISO:
- ISO-10648-1 - Containment enclosures - Part 1: Design principles
- ISO-10648-2 - Containment enclosures - Part 2: Classification according to leak tightness and associated checking methods
- ISO-10991 - Microfluidics - Vocabulary
Other SDOs:
- DIN-EN-14175-4 - Part 4: On-Site Test Methods, Fume Cupboards
- DIN-EN-14175-6 - Part 6: Variable Air Volume Fume Cupboards, Fume Cupboards
- DIN-EN-14470-2 - Part 2: Safety Cabinets for Pressurized Gas Cylinders, Fire Safety Storage Cabinets
- DIN-EN-14727 - Laboratory Furniture - Storage Units for Laboratories - Requirements & Test Methods
- DIN-EN-15154-1 - Part 1: Plumbed-in Body Showers for Laboratories, Emergency Safety Showers
- DIN-EN-15154-2 - Part 2: Plumbed-in Eye Wash Units, Emergency Safety Showers
- EN-14175-1 - Part 1: Vocabulary, Fume Cupboards
- EN-14175-2 - Part 2: Safety & Performance Requirements, Fume Cupboards
- EN-14175-3 - Part 3: Type Test Methods, Fume Cupboards
- EN-14175-4 - Fume Cupboards, On-Site Test Methods
- EN-14175-6 - Part 6: Variable Air Volume Fume Cupboards, Fume Cupboards
- EN-14175-7 - Fume cupboards - Part 7: Fume cupboards for high heat and acidic load
- EN-14470-2 - Part 2: Safety Cabinets for Pressurized Gas Cylinders, Fire Safety Storage Cabinets
- EN-14727 - Laboratory Furniture - Storage Units for Laboratories - Requirements & Test Methods
- EN-15154-1 - Emergency safety showers - Part 1: Plumbed-in body showers for laboratories
- EN-15154-2 - Part 2: Plumbed-in Eye Wash Units, Emergency Safety Showers
- EN-15154-3 - Part 3: Non-Plumbed-in Body Showers, Emergency Safety Showers
- EN-15154-4 - Part 4: Non Plumbed-in Eyewash Units, Emergency Safety Showers
- EN-61010-2-020 - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-020: Particular requirements for laboratory centrifuges
- EN-61010-2-033 - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-033: Particular requirements for hand-held multimeters and other meters, for domestic and professional use, capable of measuring mains voltage
- EN-61010-2-040 - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-040 Particular requirements for sterilizers and washer-disinfectors used to treat medical materials
- EN-61010-2-081 - Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-081: Particular requirements for automatic and semi-automatic laboratory equipment for analysis and other purposes
- EN-61010-2-091 - Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-091: Particular requirements for cabinet x-ray systems
- EN-ISO-10991 - Micro Process Engineering - Vocabulary
- IEC-61010-2-040-RL - Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 2-040: Particular requirements for sterilizers and washer-disinfectors used to treat medical materials
- IWA-23 - Interoperability of microfluidic devices - Guidelines for pitch spacing dimensions and initial device classification
- SIS-CEN/TR-16589 - Laboratory installations - Capture devices with articulated extract arm
- SIS-CEN/TS-14175-5 - Fume cupboards - Part 5: Recommendations for installation and maintenance
- SIS-CEN/TS-17441 - Laboratory installations - Ventilation systems in laboratories
- SS-EN-13150 - Workbenches for laboratories in educational institutions - Dimensions, safety and durability requirements and test methods
- SS-EN-13792 - Colour coding of taps and valves for use in laboratories
- SS-EN-14056 - Laboratory furniture - Recommendations for design and installation
- SS-EN-14175-1 - Fume cupboards - Part 1: Vocabulary
- SS-EN-14175-2 - Fume cupboards - Part 2: Safety and performance requirements
- SS-EN-14175-3 - Fume cupboards - Part 3: Type test methods
- SS-EN-14175-4 - Fume cupboards - Part 4: On-site test methods
- SS-EN-14175-6 - Fume cupboards - Part 6: Variable air volume fume cupboards
- SS-EN-14175-7 - Fume cupboards - Part 7: Fume cupboards for high heat and acidic load
- SS-EN-14175-8 - Fume cupboards - Part 8: Fume cupboards for work with radioactive materials
- SS-EN-14470-1 - Fire safety storage cabinets - Part 1: Safety storage cabinets for flammable liquids
- SS-EN-14470-2 - Fire safety storage cabinets - Part 2: Safety cabinets for pressurised gas cylinders
- SS-EN-15154-1 - Emergency safety showers - Part 1: Plumbed-in body showers for laboratories
- SS-EN-15154-2 - Emergency safety showers - Part 2: Plumbed-in eye wash units
- SS-EN-15154-3 - Emergency safety showers - Part 3: Non plumbed-in body showers
- SS-EN-15154-4 - Emergency safety showers - Part 4: Non plumbed-in eyewash units
- SS-EN-15154-5 - Emergency safety showers - Part 5: Water overhead body showers for sites other than laboratories
- SS-EN-15154-6 - Emergency safety showers - Part 6: Plumbed-in multiple nozzle body showers for sites other than laboratories
- SS-EN-16589-1 - Laboratory local exhaust devices - Part 1: General requirements and type test methods for articulated extraction arms
- SS-EN-61010-1 - Safety requirements for electrical equipment for measurement, control and laboratory use - Part 1: General requirements
- SS-EN-61010-2-081 - Safety requirements for electrical equipment for measurement, control and laboratory use - Part 2-081: Particular requirements for automatic and semi-automatic laboratory equipment for analysis and other purposes
- SS-EN-ISO-10991 - Microfluidics - Vocabulary (ISO 10991:2023)
- SS-EN-ISO-4788 - Laboratory glassware - Graduated measuring cylinders (ISO 4788:2005)
- SS-EN-ISO-4797 - Laboratory glassware - Boiling flasks with conical ground joints (ISO 4797:2015)
- SS-ISO-10648-1 - Containment enclosures - Part 1: Design principles
- SS-ISO-11933-1 - Components for containment enclosures - Part 1: Glove/bag ports, bungs for glove/bag ports, enclosure rings and interchangeable units (ISO 11933-1:1997, IDT)
- SS-ISO-11933-2 - Components for containment enclosures - Part 2: Gloves, welded bags, gaiters for remote-handling tongs and for manipulators (ISO 11933-2:1997, IDT)
- SS-ISO-11933-3 - Components for containment enclosures - Part 3: Transfer systems such as plain doors, airlock chambers, double-door transfer systems, leaktight connections for waste drums