Document Center List of Standards on Surface Treatment Including Anodization, Conversion Coating, Thermal Spraying, Etc.
ICS Code 25.220.20
Return to ICS Index.Up to Level 2:
The following documents are a part of this series:
ASTM:
- ASTM-A384 - Standard Practice for Safeguarding Against Warpage and Distortion During Hot-Dip Galvanizing of Steel Assemblies
- ASTM-B136 - Standard Method for Measurement of Stain Resistance of Anodic Coatings on Aluminum
- ASTM-B242 - Standard Guide for Preparation of High-Carbon Steel for Electroplating
- ASTM-B457 - Standard Test Method for Measurement of Impedance of Anodic Coatings on Aluminum
- ASTM-B507 - Standard Practice for Design of Articles to Be Electroplated on Racks
- ASTM-B580 - Standard Specification for Anodic Oxide Coatings on Aluminum
- ASTM-B833 - Standard Specification for Zinc and Zinc Alloy Wire for Thermal Spraying (Metallizing) for the Corrosion Protection of Steel
- ASTM-B893 - Standard Specification for Hard-Coat Anodizing of Magnesium for Engineering Applications
- ASTM-B943 - Standard Specification for Zinc and Tin Alloy Wire Used in Thermal Spraying for Electronic Applications
- ASTM-C715 - Standard Test Method for Nickel on Steel for Porcelain Enameling by Photometric Analysis
- ASTM-C756 - Standard Test Method for Cleanability of Surface Finishes
- ASTM-C810 - Standard Test Method for Nickel on Steel for Porcelain Enameling by X-Ray Emission Spectrometry
- ASTM-D1735 - Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus
- ASTM-D1978 - Standard Guide for Analysis of Electrocoat Bath Samples
- ASTM-D5009 - Standard Test Method for Evaluating and Comparing Transfer Efficiency of Spray Applied Coatings Under Laboratory Conditions
- ASTM-D5043 - Standard Practice for Field Identification of Coatings (Withdrawn 2018)
- ASTM-D5063 - Standard Guide for Use of Certification of Coating Conformance Form (Withdrawn 2021)
- ASTM-D5161 - Standard Guide for Specifying Inspection Requirements for Coating and Lining Work (Metal Substrates) (Withdrawn 2013)
- ASTM-D5162 - Standard Practice for Discontinuity (Holiday) Testing of Nonconductive Protective Coating on Metallic Substrates
- ASTM-D5382 - Standard Guide to Evaluation of Optical Properties of Powder Coatings
- ASTM-D6529 - Standard Test Method for Operating Performance of Continuous Electrodeionization Systems on Feeds from 50–1000 μS/cm (Withdrawn 2020)
- ASTM-D7396 - Standard Guide for Preparation of New, Continuous Zinc-Coated (Galvanized) Steel Surfaces for Painting
- ASTM-D870 - Standard Practice for Testing Water Resistance of Coatings Using Water Immersion
- ASTM-E1059 - Standard Practice for Designating Shapes and Sizes of Nongraphite Counter Electrodes (Withdrawn 2013)
- ASTM-E130 - Standard Practice for Designation of Shapes and Sizes of Graphite Electrodes (Withdrawn 2013)
- ASTM-E1558 - Standard Guide for Electrolytic Polishing of Metallographic Specimens
- ASTM-E1575 - Standard Practice for Pressure Water Cleaning and Cutting
- ASTM-E161 - Standard Specification for Electroformed Material and Test Sieves
- ASTM-E1920 - Standard Guide for Metallographic Preparation of Thermal Sprayed Coatings
- ASTM-E2109 - Standard Test Methods for Determining Area Percentage Porosity in Thermal Sprayed Coatings
- ASTM-E41 - Terminology Relating to Conditioning (Withdrawn 2019)
- ASTM-F1113 - Standard Test Method for Electrochemical Measurement of Diffusible Hydrogen in Steels (Barnacle Electrode)
- ASTM-F21 - Standard Test Method for Hydrophobic Surface Films by the Atomizer Test
- ASTM-F22 - Standard Test Method for Hydrophobic Surface Films by the Water-Break Test
- ASTM-F2217 - Standard Practice for Coating/Adhesive Weight Determination
- ASTM-G100 - Standard Test Method for Conducting Cyclic Galvanostaircase Polarization
- ASTM-G6 - Standard Test Method for Abrasion Resistance of Pipeline Coatings
- ASTM-G70 - Standard Test Method for Ring Bendability of Pipeline Coatings (Squeeze Test) (Withdrawn 2013)
- ASTM-G71 - Standard Guide for Conducting and Evaluating Galvanic Corrosion Tests in Electrolytes
- ASTM-G82 - Standard Guide for Development and Use of a Galvanic Series for Predicting Galvanic Corrosion Performance
BSI:
- BS-1615 - Method for specifying anodic oxidation coatings on aluminium and its alloys
- BS-3189 - Method for specifying phosphate conversion coatings for metals
- BS-3987 - Specification for anodic oxidation coatings on wrought aluminium for external architectural applications
- BS-4479-3 - Design of articles that are to be coated. Recommendations for conversion coatings
- BS-4479-4 - Design of articles that are to be coated. Recommendations for paint coatings and varnish coatings
- BS-4479-5 - Design of articles that are to be coated. Recommendations for anodic oxidation coatings
- BS-4479-7 - Design of articles that are to be coated
- BS-6161-11 - Methods of test for anodic oxidation coatings on aluminium and its alloys. Measurement of total reflectance using a photoelectric reflectometer
- BS-6161-14 - Methods of test for anodic oxidation coatings on aluminium and its alloys. Determination of infra-red reflectance
- BS-6161-15 - Methods of Test for Anodic Oxidation Coatings on Aluminium and Its Alloys, Determination
- BS-6161-18 - Methods of test for anodic oxidation coatings on aluminium and its alloys
- BS-6161-6 - Assessment of Sealing Quality by Measurement of Admittance or Impedance
- BS-EN-10329 - Steel tubes and fittings for onshore and offshore pipelines. External field joint coatings
- BS-EN-12373-1 - Aluminium and aluminium alloys. Anodizing. Method for specifying decorative and protective anodic oxidation coatings on aluminium
- BS-EN-12373-10 - Aluminium and aluminium alloys. Anodizing. Measurement of mean specific abrasion resistance of anodic oxidation coatings using an abrasive jet test apparatus
- BS-EN-12373-11 - Aluminium and aluminium alloys. Anodizing
- BS-EN-12373-12 - Aluminium and aluminium alloys. Anodizing. Measurement of reflectance characteristics of aluminium surfaces using integrating-sphere instruments
- BS-EN-12373-13 - Aluminium and aluminium alloys. Anodizing. Measurement of reflectance characteristics of aluminium surfaces using a goniophotometer or an abridged goniophotometer
- BS-EN-12373-14 - Aluminium and aluminium alloys. Anodizing. Visual determination of image clarity of anodic oxidation coatings. Chart scale method
- BS-EN-12373-15 - Aluminium and aluminium alloys. Anodizing. Assessment of resistance of anodic oxidation coatings to cracking by deformation
- BS-EN-12373-16 - Aluminium and aluminium alloys. Anodizing. Check for continuity of thin anodic oxidation coatings. Copper sulfate test
- BS-EN-12373-17 - Aluminium and aluminium alloys. Anodizing. Determination of electric breakdown potential
- BS-EN-12373-18 - Aluminium and aluminium alloys. Anodizing. Rating system for the evaluation of pitting corrosion. Chart method
- BS-EN-12373-19 - Aluminium and aluminium alloys. Anodizing. Rating system for the evaluation of pitting corrosion. Grid method
- BS-EN-12373-3 - Aluminium and aluminium alloys. Anodizing. Determination of thickness of anodic oxidation coatings. Non-destructive measurement by split-beam microscope
- BS-EN-12373-4 - Aluminium and aluminium alloys. Anodizing. Estimation of loss of absorptive power of anodic oxidation coatings after sealing by dye spot test with prior acid treatment
- BS-EN-12373-5 - Aluminium and aluminium alloys. Anodizing. Assessment of quality of sealed anodic oxidation coatings by measurement of admittance
- BS-EN-12373-7 - Aluminium and aluminium alloys. Anodizing. Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution with prior acid treatment
- BS-EN-12373-8 - luminium and aluminium alloys. Anodizing. Determination of the comparative fastness to ultra-violet light and heat of coloured anodic oxidation coatings
- BS-EN-12373-9 - Aluminium and aluminium alloys. Anodizing. Measurement of wear resistance and wear index of anodic oxidation coatings using an abrasive wheel wear test apparatus
- BS-EN-12476 - Phosphate conversion coatings of metals. Method of specifying requirements
- BS-EN-1274 - Thermal spraying. Powders. Composition, technical supply conditions
- BS-EN-12921-1 - Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours. Common safety requirements
- BS-EN-12921-2 - Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours. Safety of machines using water based cleaning liquids
- BS-EN-12921-3 - Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours. Safety of machines using flammable cleaning liquids
- BS-EN-12921-4 - Machines for surface cleaning and pretreatment of industrial items using liquids and vapours. Safety of machines using halogenated solvents
- BS-EN-13214 - Thermal Spraying - Thermal Spray Coordination - Tasks and Responsibilities
- BS-EN-1395-1 - Thermal spraying. Acceptance inspection of thermal spraying equipment
- BS-EN-1395-2 - Thermal spraying. Acceptance inspection of thermal spraying equipment
- BS-EN-1395-3 - Thermal spraying. Acceptance inspection of thermal spraying equipment
- BS-EN-1395-4 - Thermal spraying. Acceptance inspection of thermal spraying equipment
- BS-EN-1395-5 - Thermal spraying. Acceptance inspection of thermal spraying equipment. Plasma spraying in chambers
- BS-EN-1395-6 - Thermal spraying. Acceptance inspection of thermal spraying equipment
- BS-EN-1395-7 - Thermal spraying. Acceptance inspection of thermal spraying equipment
- BS-EN-14616 - Thermal spraying. Recommendations for thermal spraying
- BS-EN-14665 - Thermal spraying. Thermally sprayed coatings. Symbolic representation on drawings
- BS-EN-15311 - Thermal spraying. Components with thermally sprayed coatings. Technical supply conditions
- BS-EN-15339-2 - Thermal spraying. Safety requirements for thermal spraying equipment
- BS-EN-15340 - Thermal spraying. Determination of shear load resistance of thermally sprayed coatings
- BS-EN-15520 - Thermal spraying. Recommendations for constructional design of components with thermally sprayed coatings
- BS-EN-15648 - Thermal spraying. Component related procedure qualification
- BS-EN-16813 - Thermal spraying. Measurement of the electrical conductivity of thermal sprayed non-iron metal coatings by means of eddy current method
- BS-EN-16845-1 - Photocatalysis. Anti-soiling chemical activity using adsorbed organics under solid/solid conditions
- BS-EN-17001 - Thermal spraying. Components with thermally sprayed coatings. Coating specification
- BS-EN-17002 - Thermal spraying. Components with thermally sprayed coatings. Thermal spray procedure specification
- BS-EN-17059 - Plating and anodizing lines. Safety requirements
- BS-EN-17120 - Photocatalysis. Water purification. Performance of photocatalytic materials by measurement of phenol degradation
- BS-EN-17393 - Thermal spraying. Tubular coating tensile test
- BS-EN-22063 - Metallic and Other Inorganic Coatings - Thermal Spraying - Zinc, Aluminium and Their Alloy
- BS-EN-4707 - Aerospace series. Acid pickling of aluminium and aluminium alloys without hexavalent chromium
- BS-EN-50348 - Stationary electrostatic application equipment for non-ignitable liquid coating material. Safety requirements
- BS-EN-582 - Thermal spraying. Determination of tensile adhesive strength
- BS-EN-6111 - Aerospace series. Ethylene-propylene elastomer (EPM/EPDM). Hardness 80 IRHD for static seal elements in hydraulic systems for long-term application. Material standard
- BS-EN-6139 - Aerospace series. Cap, protective, non-metallic, for EN 6123 fitting ends
- BS-EN-657 - Thermal spraying. Terminology, classification
- BS-EN-ISO-10215 - Anodizing of aluminium and its alloys. Visual determination of image clarity of anodic oxidation coatings. Chart scale method
- BS-EN-ISO-12085 - Geometrical product specification (GPS). Surface texture. Profile method. Motif parameters
- BS-EN-ISO-12670 - Thermal spraying. Components with thermally sprayed coatings. Technical supply conditions
- BS-EN-ISO-12671 - Thermal spraying. Thermally sprayed coatings. Symbolic representation on drawings
- BS-EN-ISO-12679 - Thermal spraying. Recommendations for thermal spraying
- BS-EN-ISO-12736 - Petroleum and natural gas industries. Wet thermal insulation coatings for pipelines, flow lines, equipment and subsea structures
- BS-EN-ISO-13123 - Metallic and other inorganic Coatings. Test method of cyclic heating for thermal barrier coatings under temperature gradient
- BS-EN-ISO-13565-3 - Geometric product specifications (GPS). Surface texture: Profile method. Surfaces having stratified functional properties
- BS-EN-ISO-14232-1 - Thermal spraying. Powders
- BS-EN-ISO-14916 - Thermal spraying. Determination of tensile adhesive strength
- BS-EN-ISO-14917 - Thermal spraying. Terminology, classification
- BS-EN-ISO-14919 - Thermal spraying. Wires, rods and cords for flame and arc spraying. Classification. Technical supply conditions
- BS-EN-ISO-14920 - Thermal spraying. Spraying and fusing of self-fluxing alloys
- BS-EN-ISO-14921 - Thermal spraying. Procedures for the application of thermally sprayed coatings for engineering components
- BS-EN-ISO-14922-4 - Thermal spraying. Quality requirements of thermally sprayed structures. Elementary quality requirements
- BS-EN-ISO-14924 - Thermal spraying. Post-treatment and finishing of thermally sprayed coatings
- BS-EN-ISO-15730 - Metallic and other inorganic coatings. Electropolishing as a means of smoothing and passivating stainless steel
- BS-EN-ISO-17836 - Thermal spraying. Determination of the deposition efficiency for thermal spraying
- BS-EN-ISO-18332 - Metallic and other inorganic coatings. Definitions and conventions concerning porosity
- BS-EN-ISO-18771 - Anodizing of aluminium and its alloys. Method to test the surface abrasion resistance using glass-coated abrasive paper
- BS-EN-ISO-2063 - Thermal spraying. Metallic and other inorganic coatings. Zinc, aluminium and their alloys
- BS-EN-ISO-2063-2 - Thermal spraying. Zinc, aluminium and their alloys
- BS-EN-ISO-2085 - Anodizing of aluminium and its alloys. Check for continuity of thin anodic oxidation coatings. Copper sulfate test
- BS-EN-ISO-2143 - Anodizing of aluminium and its alloys. Estimation of loss of absorptive power of anodic oxidation coatings after sealing. Dye-spot test with prior acid treatment
- BS-EN-ISO-2360 - Non-conductive coatings on non-magnetic electrically conductive base metals. Measurement of coating thickness. Amplitude-sensitive eddy-current method
- BS-EN-ISO-27830 - Metallic and other inorganic coatings. Requirements for the designation of metallic and inorganic coatings
- BS-EN-ISO-2931 - Anodizing of aluminium and its alloys. Assessment of quality of sealed anodic oxidation coatings by measurement of admittance
- BS-EN-ISO-3210 - Anodizing of aluminium and its alloys. Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in acid solution(s)
- BS-EN-ISO-3613 - Metallic and other inorganic coatings. Chromate conversion coatings on zinc, cadmium, aluminium-zinc alloys and zinc-aluminium alloys. Test methods
- BS-EN-ISO-3882 - Metallic and other inorganic coatings. Review of methods of measurement of thickness
- BS-EN-ISO-3892 - Conversion coatings on metallic materials. Determination of coating mass per unit area. Gravimetric methods
- BS-EN-ISO-6581 - Anodizing of aluminium and its alloys. Determination of the comparative fastness to ultraviolet light and heat of coloured anodic oxidation coatings
- BS-EN-ISO-7599 - Anodizing of aluminium and its alloys. Method for specifying decorative and protective anodic oxidation coatings on aluminium
- BS-EN-ISO-7599-TC - Tracked changes. Anodizing of aluminium and its alloys. Method for specifying decorative and protective anodic oxidation coatings on aluminium
- BS-EN-ISO-8993 - Anodizing of aluminium and its alloys. Rating system for the evaluation of pitting corrosion. Chart method
- BS-EN-ISO-9717 - Metallic and other inorganic coatings. Phosphate conversion coating of metals
- BS-ISO-10074 - Anodizing of aluminium and its alloys. Specification for hard anodic oxidation coatings on aluminium and its alloys
- BS-ISO-10216 - Anodizing of aluminium and its alloys. Instrumental determination of image clarity of anodic oxidation coatings. Instrumental method
- BS-ISO-11408 - Chemical conversion coatings. Black oxide coating on iron and steel. Specification and test methods
- BS-ISO-12670 - Thermal spraying. Components with thermally sprayed coatings. Technical supply conditions
- BS-ISO-12671 - Thermal spraying. Thermally sprayed coatings. Symbolic representation on drawings
- BS-ISO-12679 - Thermal spraying. Recommendations for thermal spraying
- BS-ISO-13826 - Metallic and other inorganic coatings. Determination of thermal diffusivity of thermally sprayed ceramic coatings by laser flash method
- BS-ISO-14188 - Metallic and other inorganic coatings. Test methods for measuring thermal cycle resistance and thermal shock resistance for thermal barrier coatings
- BS-ISO-15730 - Metallic and other inorganic coatings. Electropolishing as a means of smoothing and passivating stainless steel
- BS-ISO-18332 - Metallic and other inorganic coatings. Definitions and conventions concerning porosity
- BS-ISO-18771 - Anodizing of aluminium and its alloys. Method to test the surface abrasion resistance using glass-coated abrasive paper
- BS-ISO-21164 - Metallic and other inorganic coatings. DC magnetron sputtered silver coatings for engineering purposes. Measurement of coating adhesion
- BS-ISO-2135 - Anodizing of aluminium and its alloys. Accelerated test of light fastness of coloured anodic oxidation coatings using artificial light
- BS-ISO-22462 - Metallic and other inorganic coatings. Test method for the friction coefficient measurement of chemical conversion coatings
- BS-ISO-27307 - Thermal spraying. Evaluation of adhesion/cohesion of thermal sprayed ceramic coatings by transverse scratch testing
- BS-ISO-27830 - Metallic & Other Inorganic Coatings, Guidelines for Specifying Metallic & Inorganic Co
- BS-ISO-27831-1 - Metallic and other inorganic coatings. Cleaning and preparation of metal surfaces. Ferrous metals and alloys
- BS-ISO-27831-2 - Metallic and other inorganic coatings. Cleaning and preparation of metal surfaces. Non-ferrous metals and alloys
- BS-ISO-28340 - Combined coatings on aluminium. General specifications for combined coatings of electrophoretic organic coatings and anodic oxidation coatings on aluminium
- BS-ISO-6370-1 - Vitreous and porcelain enamels. Determination of the resistance to abrasion. Abrasion testing apparatus
- BS-ISO-7583 - Anodizing of aluminium and its alloys. Terms and definitions
- BS-ISO-9587 - Metallic and other inorganic coatings. Pretreatment of iron or steel to reduce the risk of hydrogen embrittlement
- PD-CEN-15339-1 - Thermal spraying. Safety requirements for thermal spraying equipment
- PD-CEN-15339-3 - Thermal spraying. Safety requirements for thermal spraying equipment
- PD-CEN-15339-4 - Thermal spraying. Safety requirements for thermal spraying equipment
- PD-CEN-15339-5 - Thermal spraying. Safety requirements for thermal spraying equipment
- PD-CEN-15339-6 - Thermal spraying. Safety requirements for thermal spraying equipment. Spray booth, Handling system, Dust collection, Exhaust system, Filter
- PD-CEN-16599 - Photocatalysis. Irradiation conditions for testing photocatalytic properties of semiconducting materials and the measurement of these conditions
- PD-CEN-16980-1 - Photocatalysis. Continuous flow test methods
- PD-CEN-16981 - Photocatalysis. Glossary of terms
- PD-ISO-14232-2 - Thermal spraying. Powders
- PD-ISO-16689 - Anodizing of aluminium and its alloys. Experimental research on possible alternative sealing quality test methods to replace the phosphoric acid/chromic acid immersion test. Evaluation of correlations
ISO:
- ISO-10074 - Anodizing of aluminium and its alloys - Specification for hard anodic oxidation coatings on aluminium and its alloys
- ISO-10111 - Metallic and other inorganic coatings - Measurement of mass per unit area - Review of gravimetric and chemical analysis methods
- ISO-10215 - Anodizing of aluminium and its alloys - Visual determination of image clarity of anodic oxidation coatings - Chart scale method
- ISO-10216 - Anodizing of aluminium and its alloys - Instrumental determination of image clarity of anodic oxidation coatings - Instrumental method
- ISO-10289 - Methods for corrosion testing of metallic and other inorganic coatings on metallic substrates -- Rating of test specimens and manufactured articles subjected to corrosion tests
- ISO-10546 - Chemical conversion coatings - Rinsed and non-rinsed chromate conversion coatings on aluminium and aluminium alloys
- ISO-11408 - Chemical conversion coatings - Black oxide coating on iron and steel - Specification and test methods
- ISO-12670 - Thermal spraying - Components with thermally sprayed coatings - Technical supply conditions
- ISO-12671 - Thermal spraying - Thermally sprayed coatings - Symbolic representation on drawings
- ISO-12679 - Thermal spraying - Recommendations for thermal spraying
- ISO-12690 - Metallic and other inorganic coatings - Thermal spray coordination - Tasks and responsibilities
- ISO-12736 - Petroleum and natural gas industries - Wet thermal insulation coatings for pipelines, flow lines, equipment and subsea structures
- ISO-13123 - Metallic and other inorganic coatings - Test method of cyclic heating for thermal-barrier coatings under temperature gradient
- ISO-13826 - Metallic and other inorganic coatings - Determination of thermal diffusivity of thermally sprayed ceramic coatings by laser flash method
- ISO-14188 - Metallic and other inorganic coatings - Test methods for measuring thermal cycle resistance and thermal shock resistance for thermal barrier coatings
- ISO-14231 - Thermal spraying -- Acceptance inspection of thermal spraying equipment
- ISO-14232 - Thermal spraying -- Powders -- Composition and technical supply conditions
- ISO-14232-1 - Thermal spraying - Powders - Part 1: Characterization and technical supply conditions
- ISO-14232-2 - Thermal spraying - Powders - Part 2: Comparison of coating performance and spray powder chemistry
- ISO-1463 - Metallic and oxide coatings - Measurement of coating thickness - Microscopical method
- ISO-14916 - Thermal spraying - Determination of tensile adhesive strength
- ISO-14917 - Thermal spraying - Terminology, classification
- ISO-14918 - Thermal spraying - Qualification testing of thermal sprayers
- ISO-14919 - Thermal spraying - Wires, rods and cords for flame and arc spraying - Classification - Technical supply conditions
- ISO-14920 - Thermal spraying - Spraying and fusing of self-fluxing alloys
- ISO-14921 - Thermal spraying - Procedures for the application of thermally sprayed coatings for engineering components
- ISO-14922-1 - Thermal spraying -- Quality requirements of thermally sprayed structures -- Part 1: Guidance for selection and use
- ISO-14922-2 - Thermal spraying -- Quality requirements of thermally sprayed structures -- Part 2: Comprehensive quality requirements
- ISO-14922-3 - Thermal spraying -- Quality requirements of thermally sprayed structures -- Part 3: Standard quality requirements
- ISO-14922-4 - Thermal spraying -- Quality requirements of thermally sprayed structures -- Part 4: Elementary quality requirements
- ISO-14923 - Thermal spraying - Characterization and testing of thermally sprayed coatings
- ISO-14924 - Thermal spraying - Post-treatment and finishing of thermally sprayed coatings
- ISO-15730 - Metallic and other inorganic coatings -- Electropolishing as a means of smoothing and passivating stainless steel
- ISO-16348 - Metallic and other inorganic coatings - Definitions and conventions concerning appearance
- ISO-16688 - Guidelines for the selection of coating types, tests and methods of assessing the performance of coated aluminium in architectural applications
- ISO-16689 - Anodizing of aluminium and its alloys - Experimental research on possible alternative sealing quality test methods to replace the phosphoric acid/chromic acid immersion test - Evaluation of correlations
- ISO-17834 - Thermal spraying - Coatings for protection against corrosion and oxidation at elevated temperatures
- ISO-17836 - Thermal spraying - Determination of the deposition efficiency for thermal spraying
- ISO-18332 - Metallic and other inorganic coatings - Definitions and conventions concerning porosity
- ISO-18555 - Metallic and other inorganic coatings - Determination of thermal conductivity of thermal barrier coatings
- ISO-18771 - Anodizing of aluminium and its alloys - Method to test the surface abrasion resistance using glass-coated abrasive paper
- ISO-2063 - Thermal spraying - Metallic and other inorganic coatings - Zinc, aluminium and their alloys
- ISO-2063-1 - Thermal spraying - Zinc, aluminium and their alloys - Part 1: Design considerations and quality requirements for corrosion protection systems
- ISO-2063-2 - Thermal spraying - Zinc, aluminium and their alloys - Part 2: Execution of corrosion protection systems
- ISO-2064 - Metallic and other inorganic coatings - Definitions and conventions concerning the measurement of thickness
- ISO-2085 - Anodizing of aluminium and its alloys - Check for continuity of thin anodic oxidation coatings - Copper sulfate test
- ISO-2106 - Anodizing of aluminium and its alloys - Determination of mass per unit area (surface density) of anodic oxidation coatings - Gravimetric method
- ISO-2106-1 - Amendment 1 to ISO 2106:1982
- ISO-21164 - Metallic and other inorganic coatings - DC magnetron sputtered silver coatings for engineering purposes - Measurement of coating adhesion
- ISO-2128 - Anodizing of aluminium and its alloys - Determination of thickness of anodic oxidation coatings - Non-destructive measurement by split-beam microscope
- ISO-2135 - Anodizing of aluminium and its alloys - Accelerated test of light fastness of coloured anodic oxidation coatings using artificial light
- ISO-2143 - Anodizing of aluminium and its alloys - Estimation of loss of absorptive power of anodic oxidation coatings after sealing - Dye-spot test with prior acid treatment
- ISO-22462 - Metallic and other inorganic coatings - Test method for the friction coefficient measurement of chemical conversion coatings
- ISO-23052 - Anodizing of aluminium and its alloys - Test method for chemical resistance of anodic oxidation coatings on aluminium and its alloys using electromotive force apparatus
- ISO-2360 - Non-conductive coatings on non-magnetic electrically conductive base metals - Measurement of coating thickness - Amplitude-sensitive eddy-current method
- ISO-2376 - Anodizing of aluminium and its alloys - Determination of breakdown voltage and withstand voltage
- ISO-26946 - Standard method for porosity measurement of thermally sprayed coatings
- ISO-27307 - Thermal spraying - Evaluation of adhesion/cohesion of thermal sprayed ceramic coatings by transverse scratch testing
- ISO-27830 - Metallic and other inorganic coatings - Requirements for the designation of metallic and inorganic coatings
- ISO-27831-1 - Metallic and other inorganic coatings - Cleaning and preparation of metal surfaces - Part 1: Ferrous metals and alloys
- ISO-27831-2 - Metallic and other inorganic coatings - Cleaning and preparation of metal surfaces - Part 2: Non-ferrous metals and alloys
- ISO-28340 - Combined coatings on aluminium - General specifications for combined coatings of electrophoretic organic coatings and anodic oxidation coatings on aluminium
- ISO-2931 - Anodizing of aluminium and its alloys - Assessment of quality of sealed anodic oxidation coatings by measurement of admittance
- ISO-3210 - Anodizing of aluminium and its alloys - Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in acid solution(s)
- ISO-3211 - Anodizing of aluminium and its alloys - Assessment of resistance of anodic oxidation coatings to cracking by deformation
- ISO-3543 - Metallic and non-metallic coatings -- Measurement of thickness -- Beta backscatter method
- ISO-3613 - Metallic and other inorganic coatings - Chromate conversion coatings on zinc, cadmium, aluminium-zinc alloys and zinc-aluminium alloys - Test methods
- ISO-3868 - Metallic and other non-organic coatings - Measurement of coating thicknesses - Fizeau multiple-beam interferometry method
- ISO-3882 - Metallic and other inorganic coatings - Review of methods of measurement of thickness
- ISO-3892 - Conversion coatings on metallic materials -- Determination of coating mass per unit area -- Gravimetric methods
- ISO-4520 - Chromate conversion coatings on electroplated zinc and cadmium coatings
- ISO-4536 - Metallic and non-organic coatings on metallic substrates - Saline droplets corrosion test (SD test)
- ISO-4541 - Metallic and other non-organic coatings - Corrodkote corrosion test (CORR test)
- ISO-4543 - Metallic and other non-organic coatings - General rules for corrosion tests applicable for storage conditions
- ISO-6581 - Anodizing of aluminium and its alloys - Determination of the comparative fastness to ultraviolet light and heat of coloured anodic oxidation coatings
- ISO-6719 - Anodizing of aluminium and its alloys - Measurement of reflectance characteristics of aluminium surfaces using integrating-sphere instruments
- ISO-6988 - Metallic and other non organic coatings - Sulfur dioxide test with general condensation of moisture
- ISO-7583 - Anodizing of aluminium and its alloys - Terms and definitions
- ISO-7599 - Anodizing of aluminium and its alloys - Method for specifying decorative and protective anodic oxidation coatings on aluminium
- ISO-7668 - Anodizing of aluminium and its alloys - Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20 degrees, 45 degrees, 60 degrees or 85 degrees
- ISO-7759 - Anodizing of aluminium and its alloys - Measurement of reflectance characteristics of aluminium surfaces using a goniophotometer or an abridged goniophotometer
- ISO-8251 - Anodizing of aluminium and its alloys - Measurement of abrasion resistance of anodic oxidation coatings
- ISO-8252 - Anodized aluminium and aluminium alloys - Measurement of mean specific abrasion resistance of anodic oxidation coatings with an abrasive jet test apparatus
- ISO-8993 - Anodizing of aluminium and its alloys - Rating system for the evaluation of pitting corrosion - Chart method
- ISO-8994 - Anodizing of aluminium and its alloys - Rating system for the evaluation of pitting corrosion - Grid method
- ISO-9587 - Metallic and other inorganic coatings - Pretreatment of iron or steel to reduce the risk of hydrogen embrittlement
- ISO-9588 - Metallic and other inorganic coatings - Post-coating treatments of iron or steel to reduce the risk of hydrogen embrittlement
- ISO-9717 - Metallic and other inorganic coatings - Phosphate conversion coating of metals
Other SDOs:
- BS-EN-ISO-2063-1 - Thermal spraying. Zinc, aluminium and their alloys
- DIN-17611 - Anodized products of wrought aluminium and wrought aluminium alloys - Technical conditions of delivery
- DIN-EN-1274 - Thermal Spraying - Powders, Composition, Technical Supply Conditions
- DIN-EN-12921-1 - Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Part 1: Common safety requirements; German version EN 12921-1:2005+A1:2010
- DIN-EN-12921-2 - Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Part 2: Safety of machines using water based cleaning liquids; German version EN 12921-2:2005+A1:2008
- DIN-EN-12921-3 - Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Part 3: Safety of machines using flammable cleaning liquids; German version EN 12921-3:2005+A1:2008
- DIN-EN-12921-4 - Machines for surface cleaning and pretreatment of industrial items using liquids and vapours - Part 4: Safety of machines using halogenated solvents; German version EN 12921-4:2005+A1:2008
- DIN-EN-1395-1 - Part 1: General Requirements, Thermal Spraying - Acceptance Inspection of Thermal Spr
- DIN-EN-1395-2 - Part 2: Flame Spraying Including Hvof, Thermal Spraying - Acceptance Inspection of The
- DIN-EN-1395-3 - Part 3: Arc Spraying, Thermal Spraying - Acceptance Inspection of Thermal Spraying Equ
- DIN-EN-1395-4 - Part 4: Plasma Spraying, Thermal Spraying - Acceptance Inspection of Thermal Spraying
- DIN-EN-1395-5 - Part 5: Plasma Spraying in Chambers, Thermal Spraying - Acceptance Inspection of Therm
- DIN-EN-1395-6 - Part 6: Manipulator Systems, Thermal Spraying - Acceptance Inspection of Thermal Spray
- DIN-EN-1395-7 - Part 7: Powder Feed Systems, Thermal Spraying - Acceptance Inspection of Thermal Spray
- DIN-EN-14616 - Thermal spraying - Recommendations for thermal spraying
- DIN-EN-14665 - Thermal spraying - Thermal sprayed coatings - Symbolic representation on drawings; German version EN 14665:2004
- DIN-EN-15311 - Thermal spraying - Components with thermally sprayed coatings - Technical supply conditions; German version EN 15311:2007
- DIN-EN-15339-2 - Part 2: Gas Control Units, Therma Spraying - Safety Requirements for Thermal Spraying
- DIN-EN-15340 - Thermal Spraying - Determination of Shear Load Resistance of Thermally Sprayed Coating
- DIN-EN-657 - Thermal Spraying, Terminology, Classification
- DIN-EN-ISO-12671 - Thermal spraying - Thermally sprayed coatings - Symbolic representation on drawings (ISO 12671:2012)
- DIN-EN-ISO-14919 - Thermal spraying - Wires, rods and cords for flame and arc spraying - Classification - Technical supply conditions
- DIN-EN-ISO-14924 - Thermal Spraying - Post-Treatment & Finishing of Thermally Sprayed Coatings
- DIN-EN-ISO-17836 - Thermal Spraying, Determination of the Deposition Efficiency for Thermal Spraying
- DIN-EN-ISO-2063 - Thermal Spraying - Metallic & Other Inorganic Coatings, Zinc, Aluminium & Their Alloys
- EN-12373-1 - Part 1: Method for Specifying Decorative & Protective Anodicoxidation Coatings on Alum
- EN-12373-11 - Part 11: Measurement of Specular Reflectance & Specular Gloss of Anodic Oxidation Coat
- EN-12373-12 - Part 12: Measurement of Reflectance Characteristics of Aluminium Sufaces Using Intergr
- EN-12373-13 - Part 13: Measurement of Reflectance Characteristics of Aluminium Surfaces Using a Goni
- EN-12373-14 - Part 14: Visual Determination of Image Clarity of Anodic Oxidation Coatings - Chartsca
- EN-12373-15 - Part 15: Assessment of Resistance of Anodic Oxidation Coatings To Cracking by Deformat
- EN-12373-16 - Part 16: Check for Continuity of Thin Anodic Oxidation Coatings - Aluminium & Aluminiu
- EN-12373-17 - Part 17: Determination of Electric Breakdown Potential, Aluminium & Aluminium Alloys -
- EN-12373-18 - Part 18: Rating System for the Evaluation of Pitting Corrosion - Chart Method, Alumini
- EN-12373-19 - Part 19: Rating System for the Evaluation of Pitting Corrosion - Grid Method, Aluminiu
- EN-12373-4 - Aluminium & Aluminium Alloys, Anodizing, Estimation of Loss of Absorptive Power of An
- EN-12373-7 - Part 7: Assessment of Quality of Sealed Anodic Oxidation Coatings by Measurement of Th
- EN-12373-8 - Aluminium & Aluminium Alloys, Determination of the Comparative Fastness To Ultra-Viole
- EN-12373-9 - Measurement of Wear Resistance & Wear Index of Anodic Oxidation Coatings Using an Abra
- EN-1274 - Thermal Spraying - Powders, Composition, Technical Supply Conditions
- EN-12921-1 - Part 1: Common Safety Requirements, Machines for Surface Cleaning & Pre-Treatment of I
- EN-12921-2 - Part 2: Safety of Machines Using Water Based Cleaning Liquids, Machines for Surface Cl
- EN-12921-3 - Part 3: Safety of Machines Using Flammable Cleaning Liquids, Machines for Surface Clea
- EN-12921-4 - Part 4: Safety of Machines Using Halogenated Solvents, Machines for Surface Cleaning &
- EN-1395-1 - Part 1: General Requirements, Thermal Spraying - Acceptance Inspection of Thermal Spr
- EN-1395-2 - Part 2: Flame Spraying Including Hvof, Thermal Spraying - Acceptance Inspection of The
- EN-1395-3 - Part 3: Arc Spraying, Thermal Spraying - Acceptance Inspection of Thermal Spraying Equ
- EN-1395-4 - Part 4: Plasma Spraying, Thermal Spraying - Acceptance Inspection of Thermal Spraying
- EN-1395-5 - Thermal Spraying, Acceptance Inspection of Thermal Spraying Equipment, Plasma Sprayin
- EN-1395-6 - Part 6: Manipulator Systems, Thermal Spraying - Acceptance Inspection of Thermal Spray
- EN-1395-7 - Part 7: Powder Feed Systems, Thermal Spraying - Acceptance Inspection of Thermal Spray
- EN-14616 - Thermal Spraying, Recommendations for Thermal Spraying
- EN-14665 - Thermal Spraying, Thermally Sprayed Coatings, Symbolic Representation on Drawings
- EN-15311 - Thermal Spraying - Components With Thermally Sprayed Coatings - Technical Supply Condi
- EN-15339-2 - Part 2: Gas Control Units, Thermal Spraying - Safety Requirements for Thermal Spraying
- EN-15340 - Thermal Spraying - Determination of Shear Load Resistance of Thermally Sprayed Coating
- EN-15520 - Thermal Spraying, Recommendations for Constructional Design of Components With Therma
- EN-15648 - Thermal Spraying - Component Related Procedure Qualification
- EN-16813 - Thermal spraying - Measurement of the electrical conductivity of thermal sprayed non-iron metal coatings by means of eddy current method
- EN-16845-1 - Photocatalysis - Anti-soiling chemical activity using adsorbed organics under solid/solid conditions - Part 1: Dyes on porous surfaces
- EN-17001 - Thermal spraying - Components with thermally sprayed coatings - Coating specification
- EN-17002 - Thermal spraying - Components with thermally sprayed coatings - Thermal spray procedure specification
- EN-17059 - Plating and anodizing lines - Safety requirements
- EN-17120 - Photocatalysis - Water purification - Performance of photocatalytic materials by measurement of phenol degradation
- EN-4707 - Aerospace series - Acid pickling of aluminum and aluminum alloy without hexavalent chromium
- EN-657 - Thermal Spraying, Terminology, Classification
- EN-ISO-10215 - Anodizing of Aluminium & Its Alloys - Visual Determination of Image Clarity of Anodic
- EN-ISO-12085 - Geometrical Product Specifications (Gps) - Surface Texture: Profile Method - Motif Pa
- EN-ISO-12670 - Thermal spraying - Components with thermally sprayed coatings - Technical supply conditions
- EN-ISO-12671 - Thermal spraying - Thermally sprayed coatings - Symbolic representation on drawings (ISO 12671:2012)
- EN-ISO-12679 - Thermal spraying - Recommendations for thermal spraying
- EN-ISO-12736 - Petroleum and natural gas industries - Wet thermal insulation coatings for pipelines, flow lines, equipment and subsea structures
- EN-ISO-13123 - Metallic and other inorganic coatings - Test method of cyclic heating for thermal-barrier coatings under temperature gradient (ISO 13123:2011)
- EN-ISO-13565-3 - Part 3: Height Characterization Using the Material Probability Curve, Gps - Surface Te
- EN-ISO-14232-1 - Thermal spraying - Powders - Part 1: Characterization and technical supply conditions
- EN-ISO-14916 - Thermal spraying - Determination of tensile adhesive strength
- EN-ISO-14917 - Thermal spraying - Terminology, classification
- EN-ISO-14919 - Thermal spraying - Wires, rods and cords for flame and arc spraying - Classification - Technical supply conditions
- EN-ISO-14920 - Thermal spraying - Spraying and fusing of self-fluxing alloys
- EN-ISO-14922-4 - Thermal Spraying, Quality Requirements of Thermally Sprayed Structures, Elementary Qu
- EN-ISO-14924 - Thermal Spraying - Post-Treatment & Finishing of Thermally Sprayed Coatings
- EN-ISO-15730 - Metallic and other inorganic coatings - Electropolishing as a means of smoothing and passivating stainless steel
- EN-ISO-17836 - Thermal Spraying, Determination of the Deposition Efficiency for Thermal Spraying
- EN-ISO-18332 - Metallic & Other Inorganic Coatings, Definitions & Conventions Conerning Porosity
- EN-ISO-2063 - Thermal Spraying - Metallic & Other Inorganic Coatings, Zinc, Aluminium & Their Alloys
- EN-ISO-2063-1 - Thermal spraying - Zinc, aluminium and their alloys - Part 1: Design considerations and quality requirements for corrosion protection systems
- EN-ISO-2063-2 - Thermal spraying - Zinc, aluminium and their alloys - Part 2: Execution of corrosion protection systems
- EN-ISO-2085 - Anodizing of Aluminium & Its Alloys - Check for Continuity of Thin Anodic Oxidation Co
- EN-ISO-2106 - Anodizing of aluminium and its alloys - Determination of mass per unit area (surface density) of anodic oxidation coatings - Gravimetric method
- EN-ISO-2360 - Non-conductive coatings on non-magnetic electrically conductive base metals - Measurement of coating thickness - Amplitude-sensitive eddy-current method
- EN-ISO-27830 - Metallic and other inorganic coatings - Guidelines for specifying metallic and inorganic coatings (ISO 27830:2008)
- EN-ISO-2931 - Anodizing of Aluminium & Its Alloys - Assessment of Quality of Sealed Anodic Oxidatio
- EN-ISO-3210 - Anodizing of Aluminium & Its Alloys - Assessment of Quality of Sealed Anodic Oxidatio
- EN-ISO-4016 - Anodizing of aluminium and its alloys - Rating system for the evaluation of pitting corrosion - Grid method
- EN-ISO-6581 - Anodizing of Aluminium & Its Alloys - Determination of the Comparative Fastness To Ult
- EN-ISO-7599 - Anodizing of Aluminium & Its Alloys - General Specifications for Anodic Oxidation Coat
- EN-ISO-8251 - Anodizing of aluminium and its alloys - Measurement of abrasion resistance of anodic oxidation coatings (ISO 8251:2011)
- EN-ISO-8993 - Anodizing of Aluminium & Its Alloys - Rating System for the Evaluation of Pitting Cor
- EN-ISO-8994 - Anodizing of aluminium and its alloys - Rating system for the evaluation of pitting corrosion - Grid method
- EN-ISO-9717 - Metallic and other inorganic coatings - Phosphate conversion coating of metals (ISO 9717:2010)
- JIS-H-0201 - Glossary of terms used in the surface treatment of aluminium
- JIS-H-0211 - Glossary of terms used in surface treatments by dry processing
- JIS-H-8250 - Graphical symbol for thermal spraying
- JIS-H-8261-AM1 - Wires, rods and cords for flame and arc thermal spraying (Amendment 1)
- JIS-H-8300 - Thermal spraying -- Zinc, aluminium and their alloys
- JIS-H-8306 - Cermet thermal spraying
- JIS-H-8601 - Anodic oxide coatings on aluminium and aluminium alloys
- JIS-H-8603 - Hard anodic oxide coatings on aluminium and its alloys
- JIS-H-8651 - Conversion and anodic oxide coatings on magnesium and magnesium alloys
- JIS-H-8679-1 - Anodizing of aluminium and its alloys -- Rating system for the evaluation of pitting corrosion -- Part 1: Rating number method
- JIS-H-8679-2 - Anodizing of aluminium and its alloys -- Rating system for the evaluation of pitting corrosion -- Part 2: Grid method
- JIS-H-8680-1 - Test methods for thickness of anodic oxide coatings on aluminium and aluminium alloys -- Part1: Microscopical method
- JIS-H-8680-2 - Test methods for thickness of anodic oxide coatings on aluminium and aluminium alloys -- Part 2: Eddy current method
- JIS-H-8680-3 - Anodizing of aluminium and its alloys -- Determination of thickness of anodic oxidation coatings -- Part 3: Non-destructive measurement by split-beam microscope
- JIS-H-8681-1 - Test methods for corrosion resistance of anodic oxide coatings on aluminium and aluminium alloys -- Part 1: Alkali resistance test
- JIS-H-8681-2 - Test methods for corrosion resistance of anodic oxide coatings on aluminium and aluminium alloys -- Part 2: CASS test
- JIS-H-8682-1 - Anodizing of aluminium and its alloys -- Measurement of abrasion resistance of anodic oxidation coatings -- Part 1: Abrasive-wheel-wear abrasion resistance test
- JIS-H-8682-2 - Anodizing of aluminium and its alloys -- Measurement of abrasion resistance of anodic oxidation coatings -- Part 2: Abrasive jet abrasion resistance test
- JIS-H-8682-3 - Anodizing of aluminium and its alloys -- Measurement of abrasion resistance of anodic oxidation coatings -- Part 3: Falling sand abrasion resistance test
- JIS-H-8683-1 - Anodizing of aluminium and its alloys -- Estimation of loss of absorptive power of anodic oxidation coatings after sealing -- Part 1: Dye-spot test with prior acid treatment
- JIS-H-8683-2 - Anodizing of aluminium and its alloys -- Assessment of quality of sealed anodic oxidation coatings -- Part 2: Measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution
- JIS-H-8683-3 - Anodizing of aluminium and its alloys -- Assessment of quality of sealed anodic oxidation coatings -- Part 3: Measurement of admittance
- JIS-H-8685-1 - Anodizing of aluminium and its alloys -- Accelerated test of light fastness of coloured anodic oxidation coatings using artificial light
- JIS-H-8685-2 - Anodizing of aluminium and its alloys -- Determination of the comparative fastness to ultraviolet light of coloured anodic oxidation coatings
- JIS-H-8686-1 - Anodizing of aluminium and its alloys -- Visual determination of image clarity of anodic oxidation coatings -- Visual method
- JIS-H-8686-2 - Anodizing of aluminium and its alloys -- Instrumental determination of image clarity of anodic oxidation coatings -- Instrumental method
- JIS-H-8688 - Anodizing of aluminium and its alloys -- Determination of mass per unit area (surface density) of anodic oxidation coatings
- JIS-H-8689 - Anodizing of aluminium and its alloys -- Check for continuity of thin anodic oxidation coatings -- Copper sulfate test
- SIS-CEN/TS-16980-1 - Photocatalysis - Continuous flow test methods - Part 1: Determination of the degradation of nitric oxide (NO) in the air by photocatalytic materials
- SIS-CEN/TS-16981 - Photocatalysis - Glossary of terms
- SS-186011 - Anti-corrosion agents for vehicles - Fluids for hollow sections - Determination of removability and effect on car finish
- SS-186012 - Anti-corrosion agents for vehicles - Fluids for hollow sections - Determination of brittleness at low temperature
- SS-186013 - Anti-corrosion agents for vehicles - Fluids for hollow sections - Determination of effect on aluminium and copper
- SS-186014 - Anti-rust agents for vehicles - Fluids for hollowsections - Determination of applicability
- SS-186016 - Anti-corrosion agents for vehicles - Fluids for hollow sections - Determination of film weight after heat treatment
- SS-186018 - Anti-rust agents for vehicles - Fluids for hollowsections - Determination of rust protection on damp surface
- SS-186020 - Anti-corrosion agents for vehicles - Fluids for hollow sections - Determination of film weight after drying in closed space
- SS-186021 - Anti-corrosion agents for vehicles - Fluids for hollow sections and underbody agents - Determination of compatibility between different anti-corrosion agents
- SS-186022 - Anti-rust agents for vechicles - Fluids for hollow sections - Determination of adhesion at low temperature
- SS-186023 - Anti-corrosion agents for vehicles - Fluids for hollow sections - Determination of penetration in crevice
- SS-186024 - Anti-rust agents for vehicles - Fluids for hollowsections - Determination of anti-corrosion efficiency in crevice
- SS-186025 - Anti-rust agents for vehicles - Fluids for hollowsections - Test specimen for corrosion test in crevice
- SS-186026 - Anti-corrosion agents for vehicles - Fluids for hollow sections - Determination of anti-corrosion efficiency on open surface
- SS-186031 - Anti-rust agents for vehicles - Underbody agents - Determination of removability and effect on car finish
- SS-186032 - Anti-corrosion agents for vehicles - Underbody agents - Determination of brittleness at low temperature
- SS-186033 - Anti-corrosion agents for vehicles - Underbody agents - Determination of effects on aluminium and copper
- SS-186035 - Anti-corrosion agents for vehicles - Underbody agents - Determination of resistance to heat
- SS-186036 - Anti-corrosion agents for vehicles - Underbody agents - Determination of flame resistance
- SS-186037 - Anti-rust agents for vehicles - Underbody agents - Determination of adhesion at low temperature
- SS-186040 - Anti-corrosion agents for vehicles - Underbody agents - Determination of resistance to water spraying
- SS-186042 - Anti-corrosion agents for vehicles - Underbody agents - Determination of anti-corrosion efficiency
- SS-186511 - Anti-corrosion agents for vehicles - Fluids for hollow sections
- SS-186512 - Anti-corrosion agents for vehicles - Underbody agents
- SS-55900 - Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness
- SS-EN-12373-1 - Aluminium and aluminium alloys - Anodizing - Part 1: Method for specifying decorative and protective anodic oxidation coatings on aluminium
- SS-EN-12373-10 - Aluminium and aluminium alloys - Anodizing - Part 10: Measurement of mean specific abraison resistance of anodic oxidation coatings using an abrasive jet test apparatus
- SS-EN-12373-11 - Aluminium and aluminium alloys - Anodizing - Part 11: Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20º, 45º, 60º or 85º
- SS-EN-12373-12 - Aluminium and aluminium alloys - Anodizing - Part 12: Measurement of reflectance characteristics of aluminium surfaces using integrating-sphere instruments
- SS-EN-12373-13 - Aluminium and aluminium alloys - Anodizing - Part 13: Measurement of reflectance characteristics of aluminium surfaces using a goniophotometer or an abridged goniophotometer
- SS-EN-12373-14 - Aluminium and aluminium alloys - Anodizing - Part 14: Visual determination of image clarity of anodic oxidation coatings - Chart scale method
- SS-EN-12373-15 - Aluminium and aluminium alloys - Anodizing - Part 15: Assessment of resistance of anodic oxidation coatings to cracking by deformation
- SS-EN-12373-16 - Aluminium and aluminium alloys - Anodizing - Part 16: Check for continuity of thin anodic oxidation coatings - Copper sulfate test
- SS-EN-12373-17 - Aluminium and aluminium alloys - Anodizing - Part 17: Determination of electric breakdown potential
- SS-EN-12373-18 - Aluminium and aluminium alloys - Anodizing - Part 18: Rating system for the evaluation of pitting corrosion - Chart method
- SS-EN-12373-19 - Aluminium and aluminium alloys - Anodizing - Part 19: Rating system for the evaluation of pitting corrosion - Grid method
- SS-EN-12373-2 - Aluminium and aluminium alloys - Anodizing - Part 2: Determination of mass per unit area (surface density) of anodic oxidation coatings - Gravimetric method
- SS-EN-12373-3 - Aluminium and aluminium alloys - Anodizing - Part 3: Determination of thickness of anodic oxidation coatings - Non-destructive measurement by split-beam microscope
- SS-EN-12373-4 - Aluminium and aluminium alloys - Anodizing - Part 4: Estimation of loss of absorptive power of anodic oxidation coatings after sealing by dye spot test with prior acid treatment
- SS-EN-12373-6 - Aluminium and aluminium alloys - Anodizing - Part 6: Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution without prior acid treatment
- SS-EN-12373-7 - Aluminium and aluminium alloys - Anodizing - Part 7: Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution with prior acid treatment
- SS-EN-12373-8 - Aluminium and aluminium alloys - Anodizing - Part 8: Determination of the comparative fastness to ultra-violet light and heat of coloured anodic oxidation coatings
- SS-EN-12373-9 - Aluminium and aluminium alloys - Anodizing - Part 9: Measurement of wear resistance and wear index of anodic oxidation coatings using an abrasive wheel wear test apparatus
- SS-EN-1274 - Thermal spraying - Powders - Composition, technical supply conditions
- SS-EN-12921-1 - Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Part 1: Common safety requirements
- SS-EN-12921-2 - Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Part 2: Safety of machines using water based cleaning liquids
- SS-EN-12921-3 - Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Part 3: Safety of machines using flammable cleaning liquids
- SS-EN-12921-4 - Machines for surface cleaning and pretreatment of industrial items using liquids and vapours - Part 4: Safety of machines using halogenated solvents
- SS-EN-13214 - Thermal spraying - Thermal spray coordination - Tasks and responsibilities
- SS-EN-13507 - Thermal spraying - Pre-treatment of surfaces of metallic parts and components for thermal spraying
- SS-EN-1395 - Thermal spraying - Acceptance inspection of thermal spraying equipment
- SS-EN-1395-1 - Thermal spraying - Acceptance inspection of thermal spraying equipment - Part 1: General requirements
- SS-EN-1395-2 - Thermal spraying - Acceptance inspection of thermal spraying equipment - Part 2: Flame spraying including HVOF
- SS-EN-1395-3 - Thermal spraying - Acceptance inspection of thermal spraying equipment - Part 3: Arc spraying
- SS-EN-1395-4 - Thermal spraying - Acceptance inspection of thermal spraying equipment - Part 4: Plasma spraying
- SS-EN-1395-5 - Thermal spraying - Acceptance inspection of thermal spraying equipment - Part 5: Plasma spraying in chambers
- SS-EN-1395-6 - Thermal spraying - Acceptance inspection of thermal spraying equipment - Part 6: Manipulator systems
- SS-EN-1395-7 - Thermal spraying - Acceptance inspection of thermal spraying equipment - Part 7: Powder feed system
- SS-EN-14616 - Thermal spraying - Recommendations for thermal spraying
- SS-EN-14665 - Thermal spraying - Thermal sprayed coatings - Symbolic representation on drawings
- SS-EN-15311 - Thermal spraying - Components with thermally sprayed coatings - Technical supply conditions
- SS-EN-15339-2 - Thermal spraying - Safety requirements for thermal spraying equipment - Part 2: Gas control units
- SS-EN-15340 - Thermal spraying - Determination of shear load resistance of thermally sprayed coatings
- SS-EN-15520 - Thermal spraying - Recommendations for constructional design of components with thermally sprayed coatings
- SS-EN-16813 - Thermal spraying - Measurement of the electrical conductivity of thermal sprayed non-iron metal coatings by means of eddy current method
- SS-EN-16845-1 - Photocatalysis - Anti-soiling chemical activity using adsorbed organics under solid/solid conditions - Part 1: Dyes on porous surfaces
- SS-EN-17001 - Thermal spraying - Components with thermally sprayed coatings - Coating specification
- SS-EN-17002 - Thermal spraying - Components with thermally sprayed coatings - Thermal spray procedure specification
- SS-EN-17059 - Plating and anodizing lines - Safety requirements
- SS-EN-17120 - Photocatalysis - Water purification - Performance of photocatalytic materials by measurement of phenol degradation
- SS-EN-17393 - Thermal spraying - Tubular coating tensile test
- SS-EN-4707 - Aerospace series - Acid pickling of aluminium and aluminium alloys without hexavalent chromium
- SS-EN-657 - Thermal spraying - Terminology, classification
- SS-EN-ISO-10111 - Metallic and other inorganic coatings - Measurement of mass per unit area - Review of gravimetric and chemical analysis methods (ISO 10111:2019)
- SS-EN-ISO-10215 - Anodizing of aluminium and its alloys - Visual determination of image clarity of anodic oxidation coatings - Chart scale method (ISO 10215:2018)
- SS-EN-ISO-10289 - Methods for corrosion testing of metallic and other inorganic coatings on metallics substrates - Rating of test specimens and manufactured articles subjected to corrosion tests (ISO 10289:1999)
- SS-EN-ISO-12670 - Thermal spraying - Components with thermally sprayed coatings - Technical supply conditions (ISO 12670:2011)
- SS-EN-ISO-12671 - Thermal spraying - Thermally sprayed coatings - Symbolic representation on drawings (ISO 12671:2012)
- SS-EN-ISO-12679 - Thermal spraying - Recommendations for thermal spraying (ISO 12679:2011)
- SS-EN-ISO-12690 - Metallic and other inorganic coatings - Thermal spray coordination - Tasks and responsibilities (ISO 12690:2010)
- SS-EN-ISO-12736 - Petroleum and natural gas industries - Wet thermal insulation coatings for pipelines, flow lines, equipment and subsea structures (ISO 12736:2014)
- SS-EN-ISO-13123 - Metallic and other inorganic coatings - Test method of cyclic heating for thermal-barrier coatings under temperature gradient (ISO 13123:2011)
- SS-EN-ISO-14232-1 - Thermal spraying - Powders - Part 1: Characterization and technical supply conditions (ISO 14232-1:2017)
- SS-EN-ISO-14555 - Welding - Arc stud welding of metallic materials (ISO 14555:2017)
- SS-EN-ISO-1463 - Metallic and oxide coatings - Measurement of coating thickness - Microscopical method (ISO 1463:2003)
- SS-EN-ISO-14916 - Thermal spraying - Determination of tensile adhesive strength (ISO 14916:2017)
- SS-EN-ISO-14917 - Thermal spraying - Terminology, classification (ISO 14917:2017)
- SS-EN-ISO-14918 - Thermal spraying - Qualification testing of thermal sprayers (ISO 14918:2018)
- SS-EN-ISO-14919 - Thermal spraying - Wires, rods and cords for flame and arc spraying - Classification - Technical supply conditions (ISO 14919:2015)
- SS-EN-ISO-14920 - Thermal spraying - Spraying and fusing of self-fluxing alloys (ISO 14920:2015)
- SS-EN-ISO-14921 - Thermal spraying - Procedures for the application of thermally sprayed coatings for engineering components (ISO 14921:2010)
- SS-EN-ISO-14922-1 - Thermal spraying - Quality requirements of thermally sprayed structures - Part 1: Guidance for selection and use (ISO 14922-1:1999)
- SS-EN-ISO-14922-2 - Thermal spraying - Quality requirements of thermally sprayed structures - Part 2: Comprehensive quality requirements (ISO 14922-2:1999)
- SS-EN-ISO-14922-3 - Thermal spraying - Quality requirements of thermally sprayed structures - Part 3: Standard quality requirements (ISO 14922-3:1999)
- SS-EN-ISO-14922-4 - Thermal spraying - Quality requirements of thermally sprayed structures - Part 4: Elementary quality requirements (ISO 14922-4:1999)
- SS-EN-ISO-14923 - Thermal spraying - Characterization and testing of thermally sprayed coatings (ISO 14923:2003)
- SS-EN-ISO-14924 - Thermal spraying - Post-treatment and finishing of thermally sprayed coatings (ISO 14924:2005)
- SS-EN-ISO-15496 - Textiles - Measurement of water vapour permeability of textiles for the purpose of quality control (ISO 15496:2018)
- SS-EN-ISO-15730 - Metallic and other inorganic coatings - Electropolishing as a means of smoothing and passivating stainless steel (ISO 15730:2000)
- SS-EN-ISO-17834 - Thermal spraying - Coatings for protection against corrosion and oxidation at elevated temperatures (ISO 17834:2003)
- SS-EN-ISO-17836 - Thermal spraying - Determination of the deposition efficiency for thermal spraying (ISO 17836:2017)
- SS-EN-ISO-18332 - Metallic and other inorganic coatings - Definitions and conventions concerning porosity (ISO 18332:2007)
- SS-EN-ISO-18771 - Anodizing of aluminium and its alloys - Method to test the surface abrasion resistance using glass-coated abrasive paper (ISO 18771:2019)
- SS-EN-ISO-19598 - Metallic coatings - Electroplated coatings of zinc and zinc alloys on iron or steel with supplementary Cr(VI)-free treatment (ISO 19598:2016)
- SS-EN-ISO-2063 - Thermal spraying - Metallic and other inorganic coatings - Zinc, aluminium and their alloys (ISO 2063:2005)
- SS-EN-ISO-2063-1 - Thermal spraying - Zinc, aluminium and and their alloys - Part 1: Design considerations and quality requirements for corrosion protection systems (ISO 2063-1:2019)
- SS-EN-ISO-2063-2 - Thermal spraying - Zinc, aluminium and their alloys - Part 2: Execution of corrosion protection systems (ISO 2063-2:2017)
- SS-EN-ISO-2085 - Anodizing of aluminium and its alloys - Check for continuity of thin anodic oxidation coatings - Copper sulfate test (ISO 2085:2018)
- SS-EN-ISO-2106 - Anodizing of aluminium and its alloys - Determination of mass per unit area (surface density) of anodic oxidation coatings - Gravimetric method (ISO 2106:2019)
- SS-EN-ISO-2128 - Anodizing of aluminium and its alloys - Determination of thickness of anodic oxidation coatings - Non-destructive measurement by split-beam microscope (ISO 2128:2010)
- SS-EN-ISO-2143 - Anodizing of aluminium and its alloys - Estimation of loss of absorptive power of anodic oxidation coatings after sealing - Dye-spot test with prior acid treatment (ISO 2143:2010)
- SS-EN-ISO-2360 - Non-conductive coatings on non-magnetic electrically conductive base metals - Measurement of coating thickness - Amplitude-sensitive eddy-current method (ISO 2360:2017)
- SS-EN-ISO-2376 - Anodizing of aluminium and its alloys - Determination of breakdown voltage and withstand voltage (ISO 2376:2019)
- SS-EN-ISO-27830 - Metallic and other inorganic coatings - Requirements for the designation of metallic and inorganic coatings (ISO 27830:2017)
- SS-EN-ISO-2931 - Anodizing of aluminium and its alloys - Assessment of quality of sealed anodic oxidation coatings by measurement of admittance (ISO 2931:2017)
- SS-EN-ISO-3210 - Anodizing of aluminium and its alloys - Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in acid solution(s) (ISO 3210:2017)
- SS-EN-ISO-3211 - Anodizing of aluminium and its alloys - Assessment of resistance of anodic oxidation coatings to cracking by deformation (ISO 3211:2018)
- SS-EN-ISO-3543 - Metallic and non-metallic coatings - Measurement of thickness - Beta backscatter method (ISO 3543:2000)
- SS-EN-ISO-3613 - Metallic and other inorganic coatings - Chromate conversion coatings on zinc, cadmium, aluminium-zinc alloys and zinc-aluminium alloys - Test methods (ISO 3613:2010)
- SS-EN-ISO-3882 - Metallic and other inorganic coatings - Review of methods of measurement of thickness (ISO 3882:2003)
- SS-EN-ISO-3892 - Conversion coatings on metallic materials - Determination of coating mass per unit area - Gravimetric methods (ISO 3892:2000)
- SS-EN-ISO-6581 - Anodizing of aluminium and its alloys - Determination of the comparative fastness to ultraviolet light and heat of coloured anodic oxidation coatings (ISO 6581:2018)
- SS-EN-ISO-6719 - Anodizing of aluminium and its alloys - Measurement of reflectance characteristics of aluminium surfaces using integrating-sphere instruments (ISO 6719:2010)
- SS-EN-ISO-7599 - Anodizing of aluminium and its alloys - Method for specifying decorative and protective anodic oxidation coatings on aluminium (ISO 7599:2018)
- SS-EN-ISO-7668 - Anodizing of aluminium and its alloys - Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 20 degrees, 45 degrees, 60 degrees or 85 degrees (ISO 7668:2018)
- SS-EN-ISO-7759 - Anodizing of aluminium and its alloys - Measurement of reflectance characteristics of aluminium surfaces using a goniophotometer or an abridged goniophotometer (ISO 7759:2010)
- SS-EN-ISO-8251 - Anodizing of aluminium and its alloys - Measurement of abrasion resistance of anodic oxidation coatings (ISO 8251:2018)
- SS-EN-ISO-8434-1 - Metallic tube connections for fluid power and general use - Part 1: 24° cone connectors (ISO 8434-1:2018)
- SS-EN-ISO-8434-4 - Metallic tube connections for fluid power and general use - Part 4: 24o cone connectors with O-ring weld-on nipples (ISO 8434-4:1995)
- SS-EN-ISO-8503-1 - Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces (ISO 8503-1:2012)
- SS-EN-ISO-8503-2 - Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel - Comparator procedure (ISO 8503-2:2012)
- SS-EN-ISO-8503-3 - Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 3: Method for the calibration of ISO surface profile comparators and for the determination of surface profile - Focusing microscope procedure (ISO 8503-3:2012)
- SS-EN-ISO-8503-4 - Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface profile - Stylus instrument procedure (ISO 8503-4:2012)
- SS-EN-ISO-8993 - Anodizing of aluminium and its alloys - Rating system for the evaluation of pitting corrosion - Chart method (ISO 8993:2018)
- SS-EN-ISO-8994 - Anodizing of aluminium and its alloys - Rating system for the evaluation of pitting corrosion - Grid method (ISO 8994:2018)
- SS-EN-ISO-9717 - Metallic and other inorganic coatings - Phosphate conversion coating of metals (ISO 9717:2017)
- SS-EN-ISO-9974-2 - Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 2: Stud ends with elastomeric sealing (type E) (ISO 9974-2:1996)
- SS-EN-ISO-9974-3 - Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing - Part 3: Stud ends with metal-or-metal sealing (type B) (ISO 9974-3:1996)
- SS-ENV-1966 - Structural adhesives - Characterisation of a surface by measuring adhesion by means of the three point bending method
- SS-ENV-1967 - Structural adhesives - Evaluation of the effectiveness of surface treatment techniques for aluminium using a wet peel test in association with the floating roller method
- SS-ISO-10289 - Methods for corrosion testing of metallic and other inorganic coatings on metallic substrates - Rating of test specimens and manufactured articles subjected to corrosion tests
- SS-ISO-11408 - Chemical conversion coatings - Black oxide coating on iron and steel - Specification and test methods
- SS-ISO-13826 - Metallic and other inorganic coatings - Determination of thermal diffusivity of thermally sprayed ceramic coatings by laser flash method (ISO 13826:2013, IDT)
- SS-ISO-1726 - Road vehicles - Mechanical coupling between tractors and semi-trailers - Interchangeability (ISO 1726:2000, IDT)
- SS-ISO-27831-1 - Metallic and other inorganic coatings - Cleaning and preparation of metal surfaces - Part 1: Ferrous metals and alloys (ISO 27831-1:2008, IDT)
- SS-ISO-27831-2 - Metallic and other inorganic coatings - Cleaning and preparation of metal surfaces - Part 2: Non-ferrous metals and alloys (ISO 27831-2:2008, IDT)
- SS-ISO-3892 - Conversion coatings on metallic materials - Determination of coating mass per unit area - Gravimetric methods
- SS-ISO-8501-2 - Preparation of steel substrates before appliacation of paints and related products - Visual assessment of surface cleanliness - Part 2: Preparation of previously coated steel substrates after localized removal of previous coatings
- SS-ISO-8502-6 - Preparation of steel substrates before appliacation of paints and related products - Tests for the assessment of surface cleanliness - Del 6: Extraction of soluble contaminants for analysis - The Bresle method
- SS-ISO-9587 - Metallic and other inorganic coatings - Pretreatment of iron or steel to reduce the risk of hydrogen embrittlement (ISO 9587:2007, IDT)
- SS-ISO-9588 - Metallic and other inorganic coatings - Post-coating treatment of iron or steel to reduce the risk of hydrogen embrittlement (ISO 9588:2007, IDT)
- UNE-83321 - Concrete with photocatalytic activity. Determination of the degradation of nitric oxide (NO) in the air by photocatalytic materials. Continuous flow test method
- UNE-EN-16813 - Thermal spraying - Measurement of the electrical conductivity of thermal sprayed non-iron metal coatings by means of eddy current method
- UNE-EN-ISO-3613 - Metallic and other inorganic coatings - Chromate conversion coatings on zinc, cadmium, aluminium-zinc alloys and zinc-aluminium alloys - Test methods (ISO 3613:2010)